I take it that you meant it is an eMachines computer. eMachines wasacquired by Gateway in 2004, Gateway was acquired by Acer in 2007,and eMachines ceased operations in early 2013. The flashing blue light must be the power light. It normally flashes whenthe computer is in sleep mode. In that situatioRead more
I take it that you meant it is an eMachines computer. eMachines was acquired by Gateway in 2004, Gateway was acquired by Acer in 2007, and eMachines ceased operations in early 2013.
The flashing blue light must be the power light. It normally flashes when the computer is in sleep mode. In that situation, pressing a key on the keyboard should wake it.
I assume that is not the situation– The light should be on continuously and the computer should be working.
First, please confirm that it is the power light you see flashing, not the HDD (hard disk drive) access light. It typically flashes once per second while the computer is running, even though no disk access is going on.
If it is the power light, then the computer’s power supply may have gone bad, or there could be a problem in the motherboard. If you have access to a good replacement power supply, and someone who can swap the power supplies for you, that could be worth trying.
However, your computer is likely so cheap and so old that it isn’t worth buying a new power supply, especially if it isn’t certain that that is the problem.
Do the fans start up normally? If so, do they keep running, or do they stop when the blue power light starts flashing?
Does anything at all ever display on the screen? If so, is it part of the boot process, or just a message saying that the monitor isn’t getting a signal from the computer, and is going into power-saving mode?
If the fans come on and sound normal, it could be the monitor or the cable connection to the monitor that is at fault. Check that the cable is firmly connected. Try a different cable and a different monitor if they are available.
You can try this:
1. Power off the computer and unplug the power cord.
2. Disconnect all external devices.
3. Remove the battery if possible. (Refer to user manual for your model)
4. Press and hold the power button for 10 to 15 seconds to drain capacitors.
5. Plug the power cord back into the computer and press the power button.
6. Watch the front panel lights or optical drive lights, and listen for the fans.
7. If the computer boots, then power it off and reconnect external devices.
8. Restart the computer.
If that doesn’t work, look for a place near you that recycles computers. Such a place in Minneapolis takes old computers, determines which parts work and which parts are junk, wipes the good hard drives clean of all data, installs a new operating system, and sells them at extremely low prices. You may find a suitable computer there if your community has a similar outfit.
Make an image of your DOS hard disk using WinImage Professional (shareware with a limited free trial) then run DOS inside a virtual machine booting from the vhd image created. MS Virtual PC or VirtualBox are both free and very effective in running under the most up to date operating systems and 64 bRead more
Make an image of your DOS hard disk using WinImage Professional (shareware with a limited free trial) then run DOS inside a virtual machine booting from the vhd image created. MS Virtual PC or VirtualBox are both free and very effective in running under the most up to date operating systems and 64 bit hardware.
You tried the ME cd and got the same 'cyclic redundancy check' error? It could also be bad ram. You mght try running memtest. You can download a bootable CD or floppy image here:http://www.memtest.org/I recommended ver 2.11 for a computer similar to yours in a previous thread.It could also be the cdRead more
You tried the ME cd and got the same ‘cyclic redundancy check’ error? It could also be bad ram. You mght try running memtest. You can download a bootable CD or floppy image here:
Download a file to create a win98 or WinME startup floppy from bootdisk.com. When you get the floppy made, boot from it and run 'fdisk'. Hopefully it will let you remove any partitioning from the c: drive.Another option would be to download 'DelPart'. Put it on a bootable floppy and run it. DelPartRead more
Download a file to create a win98 or WinME startup floppy from bootdisk.com. When you get the floppy made, boot from it and run ‘fdisk’. Hopefully it will let you remove any partitioning from the c: drive.
Another option would be to download ‘DelPart’. Put it on a bootable floppy and run it. DelPart is a free utility that will remove stubborn partitions that fdisk can’t delete. It is perfectly safe, as long as you are careful and delete the correct partition.
Copy & Paste this into a command prompt & hit > Enter.net stop "client service for netware"If you can't get into a command prompt, use this.Lazesoft Recovery Suite Home Editionhttp://www.softpedia.com/get/System...http://www.lazesoft.com/lazesoft-re...Tutorialshttp://www.lazesoft.com/guidRead more
Copy & Paste this into a command prompt & hit > Enter. net stop “client service for netware”
Vter, My Windows 10 computer doesn't have any updates that weren'talready installed when I bought it new almost a year ago, soI'm not the best person to try to help. You have a recentupdate, the "Fall Creators Update". The layout of the StartMenu has been changed at least three times since the versiRead more
Vter,
My Windows 10 computer doesn’t have any updates that weren’t already installed when I bought it new almost a year ago, so I’m not the best person to try to help. You have a recent update, the “Fall Creators Update”. The layout of the Start Menu has been changed at least three times since the version I have. You might not be able to get the layout you want without uninstalling the update. But there are programs to make the Windows 10 Start Menu look like it was in Windows 7, so there might be programs to get it the way you want.
Not knowing what is in the newer versions, the first thing I would do is check the Personalization window in Settings to see if any new settings for the Start Menu have been added. My version has 6 on/off settings relating to the Start Menu, plus 10 more that specify which standard folders to show. Nothing that does what you want, though.
Hi,I'm replying to assist in whatever way I can. Maybe you missed your WAN settings requiring you to configure your ISP username and password. After this has been done, then set your DHCP range and set your Linksys modem router to Bridge Mode.
Hi,
I’m replying to assist in whatever way I can. Maybe you missed your WAN settings requiring you to configure your ISP username and password. After this has been done, then set your DHCP range and set your Linksys modem router to Bridge Mode.
How Do I Fix My Screen Won’t Turn On Only Blinking Blue Light
I take it that you meant it is an eMachines computer. eMachines wasacquired by Gateway in 2004, Gateway was acquired by Acer in 2007,and eMachines ceased operations in early 2013. The flashing blue light must be the power light. It normally flashes whenthe computer is in sleep mode. In that situatioRead more
acquired by Gateway in 2004, Gateway was acquired by Acer in 2007,
and eMachines ceased operations in early 2013.
The flashing blue light must be the power light. It normally flashes when
the computer is in sleep mode. In that situation, pressing a key on the
keyboard should wake it.
I assume that is not the situation– The light should be on continuously
and the computer should be working.
First, please confirm that it is the power light you see flashing, not the
HDD (hard disk drive) access light. It typically flashes once per second
while the computer is running, even though no disk access is going on.
If it is the power light, then the computer’s power supply may have gone
bad, or there could be a problem in the motherboard. If you have access
to a good replacement power supply, and someone who can swap the
power supplies for you, that could be worth trying.
However, your computer is likely so cheap and so old that it isn’t worth
buying a new power supply, especially if it isn’t certain that that is the
problem.
Do the fans start up normally? If so, do they keep running, or do they
stop when the blue power light starts flashing?
Does anything at all ever display on the screen? If so, is it part of the
boot process, or just a message saying that the monitor isn’t getting a
signal from the computer, and is going into power-saving mode?
If the fans come on and sound normal, it could be the monitor or the
cable connection to the monitor that is at fault. Check that the cable
is firmly connected. Try a different cable and a different monitor if
they are available.
You can try this:
1. Power off the computer and unplug the power cord.
2. Disconnect all external devices.
3. Remove the battery if possible. (Refer to user manual for your model)
4. Press and hold the power button for 10 to 15 seconds to drain capacitors.
5. Plug the power cord back into the computer and press the power button.
6. Watch the front panel lights or optical drive lights, and listen for the fans.
7. If the computer boots, then power it off and reconnect external devices.
8. Restart the computer.
If that doesn’t work, look for a place near you that recycles computers.
Such a place in Minneapolis takes old computers, determines which
parts work and which parts are junk, wipes the good hard drives clean
of all data, installs a new operating system, and sells them at extremely
low prices. You may find a suitable computer there if your community
has a similar outfit.
— Jeff, in Minneapolis
message edited by Jeff Root
Solved Boot With An MS-DOS Drive
Make an image of your DOS hard disk using WinImage Professional (shareware with a limited free trial) then run DOS inside a virtual machine booting from the vhd image created. MS Virtual PC or VirtualBox are both free and very effective in running under the most up to date operating systems and 64 bRead more
Solved Windows Could Not Start Because Of An Error in The Software
You tried the ME cd and got the same 'cyclic redundancy check' error? It could also be bad ram. You mght try running memtest. You can download a bootable CD or floppy image here:http://www.memtest.org/I recommended ver 2.11 for a computer similar to yours in a previous thread.It could also be the cdRead more
http://www.memtest.org/
I recommended ver 2.11 for a computer similar to yours in a previous thread.
It could also be the cdrom or hard drive (even though the HD doesn’t show any scandisk errors) but test the ram first.
Solved Format Hard Disk From DOS
Download a file to create a win98 or WinME startup floppy from bootdisk.com. When you get the floppy made, boot from it and run 'fdisk'. Hopefully it will let you remove any partitioning from the c: drive.Another option would be to download 'DelPart'. Put it on a bootable floppy and run it. DelPartRead more
Another option would be to download ‘DelPart’. Put it on a bootable floppy and run it. DelPart is a free utility that will remove stubborn partitions that fdisk can’t delete. It is perfectly safe, as long as you are careful and delete the correct partition.
DelPart
http://www.russelltexas.com/delpart…
(edit) Hopefully your install will then run ok..
The three most important things in computing:
1. Backups, 2. Backups and 3. Backups.
How Do I Keep My Mac From Timing Out
Go to System Preferences - Energy Saver - Power Adapter tab, put the Computer sleep to NeverThis is what I can think about.
This is what I can think about.
How To Uninstall Client Services For NetWare From Windows XP
Copy & Paste this into a command prompt & hit > Enter.net stop "client service for netware"If you can't get into a command prompt, use this.Lazesoft Recovery Suite Home Editionhttp://www.softpedia.com/get/System...http://www.lazesoft.com/lazesoft-re...Tutorialshttp://www.lazesoft.com/guidRead more
net stop “client service for netware”
If you can’t get into a command prompt, use this.
Lazesoft Recovery Suite Home Edition
http://www.softpedia.com/get/System…
http://www.lazesoft.com/lazesoft-re…
Tutorials
http://www.lazesoft.com/guide.html
Screenshot ( SS )
http://i.imgur.com/4HXqQKS.jpg
How to Boot a Computer from a Lazesoft Recovery USB Device
http://www.lazesoft.com/create-a-bo…
How Do I Install Nircmd
This page,http://lifehacker.com/263947/do-mor...says that NirCmd does not have any formal installation technique. Just copy it to C:/windows.
http://lifehacker.com/263947/do-mor…
says that NirCmd does not have any formal installation technique. Just copy it to C:/windows.
Solved How Do I Move My Apps From Centre Of Screen To Left Edge.
Vter, My Windows 10 computer doesn't have any updates that weren'talready installed when I bought it new almost a year ago, soI'm not the best person to try to help. You have a recentupdate, the "Fall Creators Update". The layout of the StartMenu has been changed at least three times since the versiRead more
My Windows 10 computer doesn’t have any updates that weren’t
already installed when I bought it new almost a year ago, so
I’m not the best person to try to help. You have a recent
update, the “Fall Creators Update”. The layout of the Start
Menu has been changed at least three times since the version
I have. You might not be able to get the layout you want
without uninstalling the update. But there are programs to
make the Windows 10 Start Menu look like it was in Windows 7,
so there might be programs to get it the way you want.
Not knowing what is in the newer versions, the first thing I
would do is check the Personalization window in Settings to
see if any new settings for the Start Menu have been added.
My version has 6 on/off settings relating to the Start Menu,
plus 10 more that specify which standard folders to show.
Nothing that does what you want, though.
— Jeff, in Minneapolis
Prolink W/less Router No Internet Connection
Hi,I'm replying to assist in whatever way I can. Maybe you missed your WAN settings requiring you to configure your ISP username and password. After this has been done, then set your DHCP range and set your Linksys modem router to Bridge Mode.
I’m replying to assist in whatever way I can. Maybe you missed your WAN settings requiring you to configure your ISP username and password. After this has been done, then set your DHCP range and set your Linksys modem router to Bridge Mode.
Solved Restore IBook G4 To Factory Settings Without Any Disks?
Look at the 4th answer in this thread: https://discussions.apple.com/threa...